

Complete with 2 valves ECO inspectables with function of gate valve, non-return valve and stainless steel filter.
Trusted client
Trusted delivery
16 other products in the same category:
1. The Polymer manifold for floor systems enables parallel feed of terminal fluidic terminals. 2. Limited dimensions that enable the insertion in boxes to be walled in partitioning walls 3. Manual or automatic on-off interception of the single circuits. 4. Adjustment of the flow in transit for balancing between the various circuits by means of flowmeters mounted on the manifold and equipped...
1. Divert hot water coming from the panel towards the boiler and the consumption. The ratio will be in function of inlet temperature. 2. Setting temperature 40ºC. 3. Thermostatic unit with lime protection and highspeed response. 4. Maximum water inlet temperature 110ºC. 5. Maximum working pressure 10 bar. 6. Flow rate 45 l/min. at pressure 3 bar.
1. Variable orifice cast iron double regulating globe valve according to BS 7350 standard. 2. Designed to regulate and balance the flow in heating and cooling with high precision, which means a more uniform temperature distribution. 3. Body and Bonnet in Ductil Iron. 4. PN16 flanges according to EN 1092. 5. Face to Face according to EN558-1 series 1. 6. Non-rising stem. Compact design. 7. EPDM...
WORKING CONDITIONS Maximum working pressure:25 bar Maximum working temperature : -10°C / 120°C STANDARDS Flange connection according to EN 1092-2 ISO PN 25. Test pressure according to EN 12266-1, DIN 3230, BS 6755 and ISO 5208.
1. The balancing valve is a single component device having adjustment functions and that measures cold and hot fluids transiting inside closed and open systems with following advantages: • Micrometric adjusting of the transfer flow. • Indicator of calibration reading of numerical value on the valve's hand wheel. • Possibility of checking circuit via indirect measuring of flow rate using...
1. Pre-assembled thermostatic kit. 2. Facilitates the connection from the solar panel to the boiler and simplifies the installation. 3. Thermostatic mixer valve with lime protection. 4. Diverter thermostatic valve with preset temperature at 40ºC. 5. Connectors included. 6. Non return valve with stainless steel filter. 7. Maximum water inlet temperature 110ºC.
The proposed valves have an oblique seat which offers a good adjustment precision and a resistance lower than the valves with a straight seat: head losses are small, flow more important for a same DN leads. Mounting on pipes is preferred direction indicated by an arrow on the body. The balancing valve can be used as a « stop valve. A thrust allows memorizing the valve adjustment, without...
1. The zone valve is intended for use in control terminal units such as fan-coil and boxes in heating, ventilation, and air conditioning systems. 2. The valves can be used with hot and cold water in the temperature range from 0 ºC (nonfreezing) to 94 ºC. 3. The valve is driven by hysteresis synchronous motor with spring return. 4. There are two types of motorized valves: normally closed 2-way...
USE: The 8-liter expansion tank for cold water is designed to be mounted on a small hydrophoric pump with accessories. As a result of such assembly, we get a very compact and small hydrophore set. Multipurpose tank with replaceable membrane for closed heating systems. An expansion tank with a replaceable membrane is one of the elements of protection of closed central heating systems....
1. Multifunction magnetic filter for hydraulic circuits 2. Polyamide PA66 + 30% FV diverter body 3. Cartridge body in polyamide PA66 + 30% FV 4. Cap construction in polyamide PA66 + 33% FV 5. Stainless steel filter AISI 304, 800 microns 6. EPDM PEROX as a hydraulic seal 7. Magnetic element Neodymium RE35 11.000 Gauss. 8. Brass ball valves according UNE-EN 12165 9. Manual air vent valve on...
Body of Stainless Steel AISI 304L Connection parts of brass CW617N EPDM seals and silent blocks Polymer Hand wheels and caps Derivation connection: G 3/4” (ISO 228) EUROKONUS Connections on line: Female 1" (ISO 228) Max. working pressure: 6 bar Max circuit test pressure: 10 bar (at 20°C) Differential pressure Δp max.: 1 bar Maximum working temperature: 70°C Fluid allowed: Water or Water +...
1. Brass construction acc/ UNE-EN 12165 nickel plated. 2. Gas (BSP) threaded M-F ends acc/ ISO 228/1. 3. Maximum working pressure 16 bar (PN 16). 4. Working temperature from -20ºC to 110ºC 5. Standard tare at 8 bar ±0.5 bar. 6. Outlet for hose connection.
APPLICATION: The 80l horizontal diaphragm tank for cold water is designed to be assembled with a pump with accessories. As a result of such assembly and after adding an anti-vibration hose with an elbow, we get a compact and relatively small hydrophore set. When selecting the size of the tank, it should be taken into account that the amount of water available between turning the pump off and...
error Your review appreciation cannot be sent