Range: DN50 to DN600.
- Knife Gate Valve on/off or regulation with rising stem.
- Molded monobloc body
-Unidirectional water tightness: Flow direction indicated on the body with an arrow.
- Installation between flanges ISO PN10.
- Small retention zone.
- Gate with a beveled cutting edge guided in the body with little backlash.
- Guaranteed closure, without risk of blockage.
- Standard polished gate, soft contact with the gaskets.
- Very resistant stainless steel packing flange avoids risks of breaks.
- Operating force reduced thanks to the elasticity of the gaskets.
- Pre-formed profiled sheet metal support plates from DN50 to DN300 for accessory or kit mounting.
- Full flow when fully opened, ensuring a high flow rate with low head loss.
- Flow regulation possible for pasty or abrasive fluids with installation of a deflector.
16 other products in the same category:
Range: from DN50 to DN1200.
- Knife Gate Valve on/off or regulation with rising stem.
- Molded monobloc body
- Unidirectional water tightness: Flow direction indicated on the body with an arrow.
- Installation between flanges ISO PN10.
- Small retention zone.
- Gate with a beveled cutting edge guided in the body with little backlash.
- Guaranteed closure, without risk of blockage.
- Standard...
Range: from DN50 to DN300.
- Knife Gate Valve on/off or regulation with rising stem.
- Molded monobloc body
- Unidirectional water tightness: Flow direction indicated on the body with an arrow.
- Installation between flanges ISO PN10.
- Small retention zone.
- Gate with a beveled cutting edge guided in the body with little backlash.
- Guaranteed closure, without risk of blockage.
- Standard...
- The housing and cover are made of 1.4301 stainless steel (AISI 304).
- NBR / EPDM valve circumferential seal according to ISO 1629
- Replaceable seal on the cover that prevents backflow.
- Detachable connections (screws, washers and nuts) that connect the elements are made of stainless steel.
- Nominal connection diameters in accordance with PN-EN ISO 6708.
- The valve designation meets...
GENERAL CHARACTERISTICS
Range : from DN 50 to DN 600
Function ON/OFF or regulation
Wafer threaded mounting ISO PN10
Unidirectional tightness, direction indication thanks to the arrow on the body
Small retention zone: the gate is guided in the body and has little clearance
Gland assembly: packing and O-ring (same materials as seat joint) to assure the elasticity and decrease the operating...
Range: from DN50 to DN600.
- Knife Gate Valve on/off or regulation with rising stem.
- Molded monobloc body
- Unidirectional water tightness: Flow direction indicated on the body with an arrow.
- Installation between flanges ISO PN10.
- Small retention zone.
- Gate with a beveled cutting edge guided in the body with little backlash.
- Guaranteed closure, without risk of blockage.
- Standard...
Water flow control gate. Water barriers for installation on canals, rivers, pipes, pumping stations, treatment plants and various technological facilities. Purpose: closing, regulating the flow of dirty or drinking water. Made of stainless material. Manufacture according to standard EN10088-1. Sliding elements manufactured according to EN 12163 Due to their properties and durability, they are...
Application: pumping stations, treatment plants, bio-gas plants, waterworks, hydroelectric power plants, dams, reservoirs.
Water flow control gate. Water barriers for installation on canals, rivers, pipes, pumping stations, treatment plants and various technological facilities. Purpose: closing, regulating the flow of dirty or drinking water. Made of stainless material. Manufacture according to...
Check valve offers a feed-through flow rate of 5,000 l/h (for concrete basins/tanks - 4000l/h for geomembrane basins) for a pressure loss (groundwater pressure or gas pressure needed for opening the valve) of 60 mbar (60 mm head).
Function ON/OFF or regulation. Wafer threaded mounting ISO PN10. Unidirectional tightness, direction indication thanks to the arrow on the body. Small retention zone: the gate is guided in the body and has little clearance. Gland assembly: packing and O-ring (same material as seat joint) to assure the elasticity and decrease the operating torque. Small head loss. Possibility to regulate thick...
Range: from DN100 to DN200.
-Body and plate in polyamide reinforced with 20% glass fibers.
-Low mass structure with minimum face to face -Easy and quick instauration
-Low pressure drop.
-Installation at the end of the networks on a vertical wall or a standard flange.
-Perfect seal ensured wih gasket -Optimal sealing ensured by a lip seal. Product advantage:
-Low weight for high pressure...
error Your review appreciation cannot be sent