Galvanized elbow 45° and 90° with couplings, type F

Knife gate valve with electric actuator interflange

FLANGED BALL CHECK VALVE

Standard knife gate valve, Handwheel operator

GENERAL CHARACTERISTICS Range : from DN 50 to DN 600 Function ON/OFF or regulation Wafer threaded mounting ISO PN10 Unidirectional tightness, direction indication thanks to the arrow on the body Small retention zone: the gate is guided in the body and has little clearance Gland assembly: packing and O-ring (same materials as seat joint) to assure the elasticity and decrease the operating...

Ductile iron non-rising stem knife gate valve with...

Function ON/OFF or regulation. Wafer threaded mounting ISO PN10. Unidirectional tightness, direction indication thanks to the arrow on the body. Small retention zone: the gate is guided in the body and has little clearance. Gland assembly: packing and O-ring (same material as seat joint) to assure the elasticity and decrease the operating torque. Small head loss. Possibility to regulate thick...

Ductile iron knife gate valve with double-acting...

Function ON/OFF or regulation. Wafer threaded mounting ISO PN10. Unidirectional tightness, direction indication thanks to the arrow on the body. Small retention zone: the gate is guided in the body and has little clearance. Gland assembly: packing and O-ring (same material as seat joint) to assure the elasticity and decrease the operating force. Small head loss. Possibility to regulate thick...

Hand penstocks, HDPE

MATERIALS: Frame, handle: Stainless steel AISI 304/304L - 1.4301/1.4307 or acid-resistant AISI 316/316L - 1.4401/1.4404 or any other depending on customer requirements Shut-off plate: PEHD (High Density Polyethylene). Gaskets: EPDM (or other material depending on working conditions, e.g. NBR, VITON or silicone). TIGHTNESS: The penstock is tight up to its height It is possible to make penstocks...

"MULTI" anti-backflow valve, flap valve

The materials from which the MULTI valves are made make the parts far lighter than the traditional valves as well as quick and easy to handle and install. They are very highly resistant to corrosion, UV light, thermal shocks and mechanical stress. The MULTI valve body is made from glass fibre reinforced isophtal acid polyester and coated in an isophtal acid Gel-Coat. The axle is ERTACETAL...

Galvanized elbow 90° with flange PN10, type F

Knife gate valve with lever ductile iron body -...

Range: from DN50 to DN300. - Knife Gate Valve on/off or regulation with rising stem. - Molded monobloc body - Unidirectional water tightness: Flow direction indicated on the body with an arrow. - Installation between flanges ISO PN10. - Small retention zone. - Gate with a beveled cutting edge guided in the body with little backlash. - Guaranteed closure, without risk of blockage. - Standard...

Tank floor check valve

Check valve offers a feed-through flow rate of 5,000 l/h (for concrete basins/tanks - 4000l/h for geomembrane basins) for a pressure loss (groundwater pressure or gas pressure needed for opening the valve) of 60 mbar (60 mm head).

Galvanized elbow 90° with flange PN10 and pipe...

Flap valve made of polyamide "N"

Available in DN 100, 110, 125, 160 and 200, the valve is comprised of: a recyclable 20% glass fibre reinforced Polyamide body (PA6-20FCV) a recyclable 30% glass-ball reinforced PPH door a TPE lip seal over-moulded on the door to guarantee a seal at a low level of back pressure an over-moulded TPE pipe sleeve seal. Thanks to its material, the flap valve offers good resistance against corrosion...

Galvanized T-piece, single drain with male coupling,...

Galvanized female coupling with 3 hooks and hose...

Black steel male end plug Typ F

Galvanized female coupling with reducing pipe...