Knife gate valve with lever stainless steel body - between flanges PN10
The knife gate valve is particularly suitable for the most difficult applications. Area of use: water treatment networks, pulp and paper industry, chemical plants, winemaking, cement works, pneumatic transport, storage.
Trusted client
Trusted delivery
Range: from DN50 to DN300.
- Knife Gate Valve on/off or regulation with rising stem.
- Molded monobloc body
- Unidirectional water tightness: Flow direction indicated on the body with an arrow.
- Installation between flanges ISO PN10.
- Small retention zone.
- Gate with a beveled cutting edge guided in the body with little backlash.
- Guaranteed closure, without risk of blockage.
- Standard polished gate, soft contact with the gaskets.
- Very resistant ductile iron packing flange avoids risks of breaks.
- Operating force reduced thanks to the elasticity of the gaskets.
- Pre-formed profiled sheet metal support plates from DN50 to DN300 for accessory or kit mounting.
- Full flow when fully opened, ensuring a high flow rate with low head loss.
- Flow regulation possible for pasty or abrasive fluids with installation of a deflector
PLVG6400-002EP
No customer reviews for the moment.
16 other products in the same category:
Knife gate valve with lever ductile iron body -...
Range: from DN50 to DN300. - Knife Gate Valve on/off or regulation with rising stem. - Molded monobloc body - Unidirectional water tightness: Flow direction indicated on the body with an arrow. - Installation between flanges ISO PN10. - Small retention zone. - Gate with a beveled cutting edge guided in the body with little backlash. - Guaranteed closure, without risk of blockage. - Standard...
Flat HydroFlap Non-Return Flaps, Inox
MATERIALS: Body, flap and hinge: Stainless steel AISI 304/304L - 1.4301/1.4307 or acid-resistant AISI 316/316L - 1.4401/1.4404 or any other depending on customer requirements. Gaskets: EPDM (or other material depending on working conditions, e.g. NBR, VITON or silicone). MOUNTING: Flap valves are mounted on a flat wall using anchors. It is recommended to use adhesive anchors. Sealing to the...
Hand penstocks, HDPE
MATERIALS: Frame, handle: Stainless steel AISI 304/304L - 1.4301/1.4307 or acid-resistant AISI 316/316L - 1.4401/1.4404 or any other depending on customer requirements Shut-off plate: PEHD (High Density Polyethylene). Gaskets: EPDM (or other material depending on working conditions, e.g. NBR, VITON or silicone). TIGHTNESS: The penstock is tight up to its height It is possible to make penstocks...
Knife gate valve with handwheel stainless steel body...
Function ON/OFF or regulation. Wafer threaded mounting ISO PN10. Unidirectional tightness, direction indication thanks to the arrow on the body. Small retention zone: the gate is guided in the body and has little clearance. Gland assembly: packing and O-ring (same material as seat joint) to assure the elasticity and decrease the operating torque. Small head loss. Possibility to regulate thick...
Ductile iron knife gate valve with double-acting...
Function ON/OFF or regulation. Wafer threaded mounting ISO PN10. Unidirectional tightness, direction indication thanks to the arrow on the body. Small retention zone: the gate is guided in the body and has little clearance. Gland assembly: packing and O-ring (same material as seat joint) to assure the elasticity and decrease the operating force. Small head loss. Possibility to regulate thick...
Flap valve made of polyamide "N"
Available in DN 100, 110, 125, 160 and 200, the valve is comprised of: a recyclable 20% glass fibre reinforced Polyamide body (PA6-20FCV) a recyclable 30% glass-ball reinforced PPH door a TPE lip seal over-moulded on the door to guarantee a seal at a low level of back pressure an over-moulded TPE pipe sleeve seal. Thanks to its material, the flap valve offers good resistance against corrosion...
Flap valve made of polyester, TERMINAL CHECK VALVE
Range: from DN200 to DN1500. -Body and plate in polyester resin reinforced with glass fibers. -Low mass structure with minimum face to face -Easy and quick instauration -Low pressure drop. -Installation at the end of the networks on a vertical wall or a standard flange. -Perfect seal ensured wih gasket conforming to standard NF EN681-1. Product advantage: -Low weight for high pressure...
"MULTI" anti-backflow valve, flap valve
The materials from which the MULTI valves are made make the parts far lighter than the traditional valves as well as quick and easy to handle and install. They are very highly resistant to corrosion, UV light, thermal shocks and mechanical stress. The MULTI valve body is made from glass fibre reinforced isophtal acid polyester and coated in an isophtal acid Gel-Coat. The axle is ERTACETAL...
The knife gate valve is particularly suitable for the most difficult applications. Area of use: water treatment networks, pulp and paper industry, chemical plants, winemaking, cement works, pneumatic transport, storage.
error Your review appreciation cannot be sent